reprap:xvico:x3:pro

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

reprap:xvico:x3:pro [2020/05/06 21:11] (current)
joe.wobb created
Line 1: Line 1:
 +====== XVICO X3 Pro ======
  
 +===== General Info =====
 +  * Manufacturer [[http://​www.xvico3d.com/​pd.jsp?​id=21#​_pp=111_499|xvico3d.com]]
 +
 +
 +===== Guides =====
 +====Assembly Instructions ====
 +
 +
 +====Assembly videos from Anet ====
 +
 +==== Additional assembly instructions ====
 +These are the most asked questions when assembling
 +
 +==== Calibration ====
 +Calibration is normally not needed as this is carried out by the manufacturer and stored in the factory installed firmware. Information on printer calibration:​
 +  * [[http://​reprap.org/​wiki/​Triffid_Hunter%27s_Calibration_Guide|Triffid Hunter'​s Calibration Guide on reprap.org]]
 +
 +==== Bed Center Calibration ====
 +Sometimes the center of the bed is not the actual center. When printing large prints, the skirt, brim or the object itself is printed outside the heated bed. For bed center offset calibration please read:
 +  * [[http://​www.thingiverse.com/​thing:​2280529|0scar'​s Calibration Guide on Thingiverse]]
 +
 +
 +
 +
 +==== General ====
 +
 +
 +===== Improvements =====
 +==== Safety ====
 +
 +==== Firmware ====
 +
 +
 +==== Bed Leveling ====
 +
 +  ​
 +==== Belts ====
 +
 +
 +==== Printable Things ====
 +
 +=== Frame Stabilization ===
 +
 +
 +=== Belt holder & tensioner ===
 +
 +
 +=== Filament Related ===
 +
 +
 +=== Extruder Related ===
 +
 +
 +=== Cases & Covers ===
 +
 +
 +=== Z-Endstops ===
 +
 +
 +=== others ===
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +===== Upgrades =====
 +==== Frame ====
 +
 +
 +==== Y Carriage Plate ====
 +  
 +
 +==== Heat bed temperature increase ====
 +
 +
 +==== Alternative boards ​ ====
 +  * [[reprap:​electronics:​ramps|RAMPS 1.4]]
 +
 +==== Hardware ​ ====
 +
 +
 +=== Extruder ===
 +
 +
 +==== Enclosure ====
 +  * <​del>​[[https://​www.thingiverse.com/​thing:​1843235|Ikea Lack Enclosure]] - cheap enclosure for Anet A8 using Ikea Lack tables</​del>​ dead link (on [[https://​web.archive.org/​web/​20171215230755/​thingiverse.com/​thing:​1843235| archive.org]])
 +  * [[https://​www.thingiverse.com/​thing:​2864118|Original Prusa i3 MK3 ENCLOSURE -Ikea Lack table]] - Another enclosure
 +
 +
 +==== ATX PSU ==== 
 +
 +  * [[reprap:​electronics:​heatbed_mosfet#​increasing_voltage_on_the_stock_psu|Increasing Voltage On the stock PSU]]
 +===== Replacement parts =====
 +
 +^ Part      ^ Description ​     ^ Where to buy?         ^
 +
 +===== Slicer Configuration =====
 +  * Set to Creality CR-10 in Cura.
 +
 +
 +==== Communities ====
 +  * Facebook group: XViCO 3D printer owners
  • reprap/xvico/x3/pro.txt
  • Last modified: 2020/05/06 21:11
  • by joe.wobb