no way to compare when less than two revisions
Differences
This shows you the differences between two versions of the page.
Last revision | |||
— | reprap:xvico:x3:pro [2020/05/06 23:11] – created joe.wobb | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== XVICO X3 Pro ====== | ||
+ | ===== General Info ===== | ||
+ | * Manufacturer [[http:// | ||
+ | |||
+ | |||
+ | ===== Guides ===== | ||
+ | ====Assembly Instructions ==== | ||
+ | |||
+ | |||
+ | ====Assembly videos from Anet ==== | ||
+ | |||
+ | ==== Additional assembly instructions ==== | ||
+ | These are the most asked questions when assembling | ||
+ | |||
+ | ==== Calibration ==== | ||
+ | Calibration is normally not needed as this is carried out by the manufacturer and stored in the factory installed firmware. Information on printer calibration: | ||
+ | * [[http:// | ||
+ | |||
+ | ==== Bed Center Calibration ==== | ||
+ | Sometimes the center of the bed is not the actual center. When printing large prints, the skirt, brim or the object itself is printed outside the heated bed. For bed center offset calibration please read: | ||
+ | * [[http:// | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ==== General ==== | ||
+ | |||
+ | |||
+ | ===== Improvements ===== | ||
+ | ==== Safety ==== | ||
+ | |||
+ | ==== Firmware ==== | ||
+ | |||
+ | |||
+ | ==== Bed Leveling ==== | ||
+ | |||
+ | | ||
+ | ==== Belts ==== | ||
+ | |||
+ | |||
+ | ==== Printable Things ==== | ||
+ | |||
+ | === Frame Stabilization === | ||
+ | |||
+ | |||
+ | === Belt holder & tensioner === | ||
+ | |||
+ | |||
+ | === Filament Related === | ||
+ | |||
+ | |||
+ | === Extruder Related === | ||
+ | |||
+ | |||
+ | === Cases & Covers === | ||
+ | |||
+ | |||
+ | === Z-Endstops === | ||
+ | |||
+ | |||
+ | === others === | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Upgrades ===== | ||
+ | ==== Frame ==== | ||
+ | |||
+ | |||
+ | ==== Y Carriage Plate ==== | ||
+ | |||
+ | |||
+ | ==== Heat bed temperature increase ==== | ||
+ | |||
+ | |||
+ | ==== Alternative boards | ||
+ | * [[reprap: | ||
+ | |||
+ | ==== Hardware | ||
+ | |||
+ | |||
+ | === Extruder === | ||
+ | |||
+ | |||
+ | ==== Enclosure ==== | ||
+ | * < | ||
+ | * [[https:// | ||
+ | |||
+ | |||
+ | ==== ATX PSU ==== | ||
+ | |||
+ | * [[reprap: | ||
+ | ===== Replacement parts ===== | ||
+ | |||
+ | ^ Part ^ Description | ||
+ | |||
+ | ===== Slicer Configuration ===== | ||
+ | * Set to Creality CR-10 in Cura. | ||
+ | |||
+ | |||
+ | ==== Communities ==== | ||
+ | * Facebook group: XViCO 3D printer owners |