reprap:anet:electronics:mainboard

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
reprap:anet:electronics:mainboard [2017/04/26 11:43] – [Anet Mainboard(s)] sjoukereprap:anet:electronics:mainboard [2018/12/02 02:27] (current) – external edit 127.0.0.1
Line 1: Line 1:
 ====== Anet Mainboard(s) ====== ====== Anet Mainboard(s) ======
-{{:reprap:anet:url.jpg?300|}}+{{:reprap:anet:url.jpg?150|}}
  
 So far the mainboard has been changed a couple of times without the version number being upgraded.  So far the mainboard has been changed a couple of times without the version number being upgraded. 
Line 7: Line 7:
 **Changes visible are:**  **Changes visible are:** 
  
-  *   4 potentiometers to set the steppermotor current(s).+  *   4 potentiometers to set the steppermotor current(s). they are visible just left of the big round capacitors
  {{:reprap:anet:electronics:4pots.jpg?300|}} -   {{:reprap:anet:electronics:4pots.jpg?300|}} - 
  
   *   1 potentiometer (right Z steppermotor only).    *   1 potentiometer (right Z steppermotor only). 
-{{:reprap:anet:electronics:1pot.jpg?300|[[http://example.com|External Link]]}}   +{{:reprap:anet:electronics:1pot.jpg?300|}}   
  
-*   No potentiometers. +  *   No potentiometers. 
- +{{:reprap:anet:electronics:0pot.jpg?300|}}
-*   changed (upgraded) powerconnectors(note the power connections switched position as well)+
  
 +  *   changed (upgraded) powerconnectors. (note the power supply connections switched position as well)
  
 +{{:reprap:anet:electronics:oldconn.jpg?400|}} **⇐ OLD  -  NEW ⇒** {{:reprap:anet:electronics:upgrconn.jpg?100|}}
  
       NOTE: The upgrade has been done because the "old" slide-on connectors often suffered meltdowns as a result of transitional resistance and the following heatdevelopement caused by improper wiring or currents going over the maximum rating for the connectors.       NOTE: The upgrade has been done because the "old" slide-on connectors often suffered meltdowns as a result of transitional resistance and the following heatdevelopement caused by improper wiring or currents going over the maximum rating for the connectors.
  
              
-{{:reprap:anet:electronics:oldconn.jpg?400|}} - {{:reprap:anet:electronics:upgrconn.jpg?100|}} 
- 
 **The general layout of the other connectors on the board stayed the same however so the picture under shows how and where to connect all plugs.** **The general layout of the other connectors on the board stayed the same however so the picture under shows how and where to connect all plugs.**
  
Line 34: Line 33:
 ===== Hardware ===== ===== Hardware =====
 === Stepper Driver === === Stepper Driver ===
-A4988 according to [[https://www.facebook.com/groups/1068531466501015/permalink/1332089536811872]]+A4988 (confirmed by removing heatsink)
  
-DRV8825 according to [[https://www.facebook.com/groups/1068531466501015/permalink/1325029870851172]] 
 === Connectors === === Connectors ===
 {{:reprap:anet:electronics:anetboardj3.jpg?direct&200|}} {{:reprap:anet:electronics:anetboardj3.jpg?direct&200|}}
  • reprap/anet/electronics/mainboard.1493199792.txt.gz
  • Last modified: 2018/12/02 02:27
  • (external edit)