reprap:anet:a8:replace_hb_connector

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

reprap:anet:a8:replace_hb_connector [2018/08/04 09:35] – [Strain relief] sjoukereprap:anet:a8:replace_hb_connector [2021/09/02 21:59] (current) – external edit 127.0.0.1
Line 1: Line 1:
-====== Replacing the heat bed connector ====== +====== Replacing the hotbed connector ====== 
-- article under development, please add your knowlage and feel free to edit -+- article under development, please add your knowledge and feel free to edit -
 The corresponding discussion can be found [[https://www.facebook.com/groups/OFFICIALAnet3DprinterSupportGroup/permalink/662020787319819/|here]] The corresponding discussion can be found [[https://www.facebook.com/groups/OFFICIALAnet3DprinterSupportGroup/permalink/662020787319819/|here]]
  
Line 6: Line 6:
 {{ :reprap:anet:a8:18449265_10211516226635514_3997977419206089998_o.jpg?direct&400 |}} {{ :reprap:anet:a8:18449265_10211516226635514_3997977419206089998_o.jpg?direct&400 |}}
  
 +For problems on the other end of these wires look here https://3dprint.wiki/reprap/electronics/heatbed_mosfet
 ==== Root cause ==== ==== Root cause ====
 There are several opinions about the root cause of this problem. Which is the main root cause or if it is a combination of them is still to be [[https://www.facebook.com/groups/OFFICIALAnet3DprinterSupportGroup/permalink/662020787319819/|discussed]]. Here some collected facts and arguments. There are several opinions about the root cause of this problem. Which is the main root cause or if it is a combination of them is still to be [[https://www.facebook.com/groups/OFFICIALAnet3DprinterSupportGroup/permalink/662020787319819/|discussed]]. Here some collected facts and arguments.
Line 31: Line 32:
  
 ==== Option 1 - Replace the connectors with the same type ==== ==== Option 1 - Replace the connectors with the same type ====
 +=== (and maybe set yourself up for another happening of "more of the same"?) ===
 +
 You will need:  You will need: 
   * 1x VHR-6N from JST   * 1x VHR-6N from JST
Line 46: Line 49:
 ==== Option 2 - Soldering the wires directly onto the hotbed heater ==== ==== Option 2 - Soldering the wires directly onto the hotbed heater ====
    Soldering cables directly onto the heater is a very reliable option if it is well done. But soldering thick wires onto the heater with     Soldering cables directly onto the heater is a very reliable option if it is well done. But soldering thick wires onto the heater with 
-   a large thermal capacity is quite dificult and requires some soldering experiance to avoid cold joints. As this connection has to +   a large thermal capacity is quite dificult and requires some soldering experience to avoid cold joints (stacking one blob of solder on  
 +   top of another without melting the solder properly, and therefor not creating a good electrical connection). As this connection has to 
    withstand a quite high current and a failure may lead to fire, this not recommended for a first time soldering experience.    withstand a quite high current and a failure may lead to fire, this not recommended for a first time soldering experience.
  
Line 59: Line 63:
   *  The solder on the heat bed is probably lead free solder. Most people use leaded solder at home. As mixing them is not recommended it is better to remove as much old solder as possible before soldering.   *  The solder on the heat bed is probably lead free solder. Most people use leaded solder at home. As mixing them is not recommended it is better to remove as much old solder as possible before soldering.
    
-  *  Foresee a strain relief so that the constant bending of the wire does not stress the solderjoint+  *  Maybe add a strain relief so that the constant bending of the wire does not stress the solderjoint.
    
-[[https://www.youtube.com/watch?v=8XAr6ac-lLU&feature=youtu.be|video of a heat bed soldering]]+[[https://www.youtube.com/watch?v=8XAr6ac-lLU&feature=youtu.be|video of a heat bed soldering]] it might be a slow going video but a lot can be learned for thoose who never practised soldering before.
  
 ==== Option 3 - spade connectors ==== ==== Option 3 - spade connectors ====
--feel free to write this chapter - +-feel free to write this chapter - always keep in mind : **if it works**, there is no wrong way of fixing your problem just easy and hard ways
 ==== Option 4 - european style screw connectors ==== ==== Option 4 - european style screw connectors ====
--feel free to write this chapter - +-feel free to write this chapter - always keep in mind : **if it works**, there is no wrong way of fixing your problem just easy and hard ways
 ===== Strain relief ===== ===== Strain relief =====
 A strain relief reduces the stress on the connector/solder. This is a good idea independently of which option was chosen or as a preventive measure before it fails. Here some options: A strain relief reduces the stress on the connector/solder. This is a good idea independently of which option was chosen or as a preventive measure before it fails. Here some options:
Line 72: Line 76:
   * 90° angle connector [[https://www.thingiverse.com/thing:17916]]   * 90° angle connector [[https://www.thingiverse.com/thing:17916]]
   * https://www.thingiverse.com/thing:1875869   * https://www.thingiverse.com/thing:1875869
 +  * https://www.wikihow.com/Identify-Resistors
  
    NOTE     NOTE 
Line 81: Line 86:
    then maybe 15 degrees spread out over ca 30 cm. therefore hardly any bending at all in a specific place and furthermore eliminating the     then maybe 15 degrees spread out over ca 30 cm. therefore hardly any bending at all in a specific place and furthermore eliminating the 
    need for the other mentioned angled connector(s). (Why overengeneer things?)    need for the other mentioned angled connector(s). (Why overengeneer things?)
 +   
        
 ===== Remarks: ===== ===== Remarks: =====
  • reprap/anet/a8/replace_hb_connector.1533368122.txt.gz
  • Last modified: 2018/12/02 02:27
  • (external edit)