Differences

This shows you the differences between two versions of the page.

--- reprap:anet:a8:firmware:adaptingmarlin [2016/12/22 00:03] – lukeskymuh
+++ reprap:anet:a8:firmware:adaptingmarlin [2016/12/22 00:56] – lukeskymuh
@@ Line 1: / Line 1: @@
 ==== Addapting Marlin to the A8 & Ramps 1.4====
 In configuration.h
-#define BAUDRATE 115200 (recomended to be more realiable)
-select the display
+#define BAUDRATE 115200 //recomended to be more realiable)
+#define TEMP_SENSOR_0 5
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_3 0
+#define TEMP_SENSOR_BED 5
+#define BED_MAXTEMP 130
+#if DISABLED(ENDSTOPPULLUPS)
+  // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
+  #define ENDSTOPPULLUP_XMAX
+  #define ENDSTOPPULLUP_YMAX
+  #define ENDSTOPPULLUP_ZMAX
+  #define ENDSTOPPULLUP_XMIN
+  #define ENDSTOPPULLUP_YMIN
+//  #define ENDSTOPPULLUP_ZMIN
+//  #define ENDSTOPPULLUP_ZMIN_PROBE
+#endif
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
+#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+// Travel limits after homing (units are in mm)
+#define X_MIN_POS 0
+#define Y_MIN_POS 0
+#define Z_MIN_POS 0
+#define X_MAX_POS 220
+#define Y_MAX_POS 220
+#define Z_MAX_POS 240
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100, 100, 400,90}  // default steps per unit for anet a8
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {200,  200, 800,180}                              // for 1/32 steps
+#define DEFAULT_MAX_FEEDRATE         {400, 400, 4, 50}
+#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 1000, 10000 }
+#define DEFAULT_ACCELERATION          1000    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
+#define FIX_MOUNTED_PROBE
+#define AUTO_BED_LEVELING_LINEAR
+  #define LEFT_PROBE_BED_POSITION   35
+  #define RIGHT_PROBE_BED_POSITION  200
+  #define BACK_PROBE_BED_POSITION   180
+  #define FRONT_PROBE_BED_POSITION  20
+select the display:
 #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+// Disables axis when it's not being used.
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
+#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
 #if DISABLED(ENDSTOPPULLUPS)
@@ Line 25: / Line 97: @@
 #define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+// Travel limits after homing
+#define X_MAX_POS 225
+#define X_MIN_POS -33
+#define Y_MAX_POS 225
+#define Y_MIN_POS -10
+#define Z_MAX_POS 245
+#define Z_MIN_POS 0