====== Hypercube ======

{{:printers:opensource:hypercube.jpg?200|}} 

The [[http://www.thingiverse.com/thing:1752766|HyperCube]] is a design by [[http://www.thingiverse.com/Tech2C/|Tech2C]] using 20x20 aluminium profiles. The printer is generally very lightweight, and uses CoreXY kinematics.

You can check out the build with a ton of very useful information on [[http://www.thingiverse.com/Tech2C/|Tech2C]]'s youtube channel: [[https://www.youtube.com/playlist?list=PLIaArjwViQRVAERWRrYfe9rtiwvvRGCzw|Build Log Video Playlist]]



====== BOM ======
==== Frame ====
T-Slot 2020 Aluminium Extrusion Profiles for X200 x Y200 x Z155 print bed area

  * 4 x 340mm (X)
  * 4 x 303mm (Y)
  * 4 x 350mm (Z)
  * 2 x 285mm (Bed)
  * 1 x 135mm (Bed)

==== Fixings ====
  * 60 x M5x8mm button head screws (for corner brackets)
  * 60 x M5x10mm button head screws (for plastic parts)
  * 2 x 100pcs T-Slot M5 hammer nuts
  * 3 x 10pcs Aluminium Corner Brackets
  * 45 x M3x10mm pan head screws
  * 45 x M3x20mm pan head screws
  * 2 x M3x6mm pan head screws
  * 2 x M3x35mm pan head screws
  * 35 x M3 Nyloc nuts
  * 35 x M3 hex nuts

==== CoreXY + Z + Bowden Drive System ====
  * 2 x 8mmx300mm Hardened Steel smooth rod (choose 300mm length) for Y axis
  * 2 x 8mmx340mm Hardened Steel smooth rod (choose 380mm length) for Z axis
  * 2 x 10mmx360mm Anodised Aluminium Rod/Tube for X axis
  * 1 x 10pcs SF-1 Self Lubricating Composite Bearing Bushing
  * 6 x LM8UU linear bearing
  * 1 x T8 300mm Lead Screw
  * 1 x 5x8mm Aluminium Flexible Shaft Coupler
  * 1 x 10pcs F608ZZ Flange Bearing
  * 2 x 10pcs F623ZZ Flange Bearing
  * 1 x 5M GT2 Belt and 2 x 20 Tooth Pulleys
  * 1 x Teflon PTFE Tube
  * 1 x MK7 Extruder Gear
  * 1 x Push Fit Connector M5

==== Motors, Electronics and Accessories ====
  * 4 x NEMA17 Stepper Motor
  * 1 x 3pcs Endstop Switch
  * 1 x RAMPS 1.4 Controller + MEGA2560 R3 + A4988 With Heat Sink Kit
  * 1 x 12V DC 50mm Blow Radial Cooling Fan
  * 1 x Heatbed Aluminium MK3 12V 24V
  * 1 x 12V 30A 360W Switching Power Supply
  * 1 x Thermistor 100K With 1M Cable for Heat Bed
  * 1 x DC power wire (choose 14AWG)
  * 1 x 10M Tinned Copper 22AWG 2 Pin Red Black
  * 5 x Bed levelling screw/spring/knob
  * 1 x Genuine E3Dv6 or Genuine Lite6 or Clone (long version)
  * 1 x Inductive Proximity Sensor

==== Print settings ====
  * 3 Perimeters
  * 3 top/bottom layers
  * 0.25mm layer height (or better)
  * 50% infill

=== Print 1 of everything except below ===
2 x <nowiki>Z_Carriage   </nowiki>   
4 x <nowiki>Z_Carriage_Clamp   </nowiki>  
4 x <nowiki>Z_Shaft_Clamp_v1.1    </nowiki>  
2 x <nowiki>XY_Clamp   </nowiki>  
2 x <nowiki>XY_Joiner   </nowiki>   
2 x <nowiki>XY_Idler   </nowiki>  
3 x <nowiki>Y_Shaft_Clamp    </nowiki>  
4 x <nowiki>Bed_Support_v1.1   </nowiki>   
2 x <nowiki>Dual_Bushing_Holder </nowiki>